3.5 inch TFT LCD Touch Screen + Protective Case

Support Cooling Fan + Touch Pen Kit For Raspberry Pi 3B+/3B/2B

$21.99
Tax excluded Delivery: 1 to 3 weeks
10 Items
  • Security is our top and the most important priority. VARPIX protects your personal data and information against unauthorized processing and against accidental loss, damage or destruction. Security is our top and the most important priority. VARPIX protects your personal data and information against unauthorized processing and against accidental loss, damage or destruction.
  • Please allow between 15-45 days for your order to arrive. If more than 45 days have passed please contact us to review the status of your order. Please allow between 15-45 days for your order to arrive. If more than 45 days have passed please contact us to review the status of your order.
  • We offer 30 days return policy, returns are subject to approval, please contact us for any question. We offer 30 days return policy, returns are subject to approval, please contact us for any question.
Introduction :
 
Sometimes you use the the Raspberry Pi with 3.5 inch touchscreen , but sometime you don't use them together. In this situation , you need a case which both suitable for Raspberry Pi alone or with 3.5 inch touchscreen. This is the reason we provide this new case -- for  the people use 3.5 inch screen more convenient: When you use the touchscreen , just remove the cover board and fan; When you don't use the touchscreen , you can use the cover and fan , which become a normal case.
 
Please note that you can't use the 3.5 inch touchscreen and cooling fan at the sametime !

 

Features :
 
1. One case for two use :
​1). This case suport install 3.5 inch touchscreen , and need to remove the cover board and can't use the fan in this using way.
2). When you don't use the 3.5 inch touchscreen , it is a general case with cooling fan. 
 
2. Full access for Raspberry Pi : 
We leave every hole for SD card , HDMI , AV , Ethernet , USB , POE , Camera , MIPI DSI ports.
 
3. Support cooling fan :
You can install the cooling fan on the cover board , which make the best heat dissipation and extend the using life of Raspberry Pi.
( You can't use the 3.5 inch touchscreen and cooling fan at the sametime ! )
 
4. Hange hole on the bottom :
We make 2 hole on the bottom so that you can hange the case on the wall or something else .
This design is very convenient when using the 3.5 inch touchscreen.

-480×320 pixel resolution, better display.
-Driver provided (works with custom Raspbian directly).
-Supports any revision of Rasp Pi (directly-pluggable).
-Designed for Raspberry Pi, an ideal alternative solution for monitor.
-Support software keyboard (system interaction without keyboard/mouse).
-Provides the best available protection/accessibility for Model B
Protect and secure your Rasp Pi from shocks, scratches and dust.
 
How to install the 3.5 inch touchscreen :
 
1). Install the Raspberry Pi on the base board 
2). ​Please stick the pad on  the back of 3.5 inch touchscreen , then insert the 3.5 inch touchscreen on Raspberry Pi by GPIO pin correctly ( don't be malposed ) 
3). Install the cover board 


Parameter:

LCD TypeTFT
LCD InterfaceSPI
Touch Screen TypeResistive
Touch Screen ControllerXPT2046
Colors65536
BacklightLED
Resolution320*480 (Pixel)
Aspect Ratio8:5
Power ConsumptionTBD
Backlight CurrentTBD
Operating Temp. (Centigrade)TBD


Interface Definition:

PIN NO.SYMBOLDESCRIPTION
1, 173.3VPower positive (3.3V power input)
2, 45VPower positive (5V power input)
3, 5, 7, 8, 10, 12, 13, 15, 16NCNC
6, 9, 14, 20, 25GNDGround
11TP_IRQTouch Panel interrupt, low level while the Touch Panel detects touching
18LCD_RSInstruction/Data Register selection
19LCD_SI / TP_SISPI data input of LCD/Touch Panel
21TP_SOSPI data output of Touch Panel
22RSTReset
23LCD_SCK / TP_SCKSPI clock of LCD/Touch Panel
24LCD_CSLCD chip selection, low active
26TP_CSTouch Panel chip selection, low active
 

 

About the system of 3.5 touch screen

The touch screen need to configure the driver for touch function , otherwise you can not use it by your own system.
Here we provide the method to configure for Raspbian system :

Step 1: Download the Raspbian IMG  
Step 2: Burn the system image
If you don't know how to do that,you can refer to the Raspberry Pi office tutorial
Step 3: Open terminal(SSH) and install the driver on RaspberryPi
(tested on RaspberryPi 3B+,3B,2B,2B+,1B,ZERO)

Run:
sudo rm -rf LCD-show
git clone https://github.com/goodtft/LCD-show.git
chmod -R 755 LCD-show
cd LCD-show/
sudo ./LCD35-show
Wait A Few Minutes, when the system reboot ok, you can see that.


You can also download the system image which we already configured well by following links :

1. for Raspberry Pi 3 :
https://mega.nz/#!vc4zjRRR!A9OMnL4tVjXUwH5Tt4T0ES2WxJyA4DGUg-gid_JHQVA

2. for Raspberry Pi 3 Modle B+ :
https://mega.nz/#!SQRl3BSS!ZwuE1VsoQSpUwHm2sa6zk1GPsU36M7793Q35NvdSYVY

or refer to configure it by this link :
https://github.com/goodtft/LCD-show


Package included:

1 x 3.5 inch Touch Screen
1 x Protective Case
1 x Touch Pen













 

10 Items
New product

No customer reviews for the moment.

  • Name : BestDeals Store Return Policy
  • Description

    BestDeals Store Return Policy

  • Click here to get more details